|
|
|
|
|
![]()
Click Image to Enlarge
|
|
Yorkville
YSM2P-2
Item #YSM2P-2
List Price:
$229.00
Your Price:
$183.20
$183.20
|
|
|
Different Views & Angles
|
|
|
|
|
Description
Specification
Video
Manual
Review
YSM2P-2
Powered Monitor - 46w, 5.25 inch
The YSM2P-II powered speaker enclosure system is an advanced studio monitor. It is equally at home in a professional recording studio, project studio, or even a living room. Development of the renowned YSM1P has helped us provide the YSM2P-II with functionality and user-friendliness at a truly reasonable cost. Components include a 1-inch domed tweeter and a 5 1/4-inch woofer. The woofer is a low-resonance 4-ohm driver fabricated with a woven laminate cone (which helps promote use of the full 32 watts of power from the YSM2P’s internal LF amplifier). The HF side of amplifier is capable of delivering up to 14 watts to the 1-inch, high-performance tweeter. Optimal performance is also achieved by use of an active crossover specifically developed for the YSM2P. The YSM2P-II also features an input trim control for precision tweaking according to room acoustics.
A smooth frequency response gives the YSM2P-II ample source representation without equalization. A precisely tuned active crossover enables each driver to take advantage of the bi-amplification. ¼-inch or XLR input jacks allow for maximum versatility.
The input, located at the rear of the enclosure, accepts line-level signal only (not speaker level). It is ideal to use balanced, shielded cables with a ¼-inch (TRS) or XLR connector however unbalanced 1/4-inch jacks can also be used. Each YSM2P-II should be connected to a single line-level source (e.g., the Right or Left line output from a mixer or preamp). If you want to use multiple YSM2Ps, they can be interconnected using "Y" adaptors.
The Input Trim control allows you to adjust the volume of each monitor until the desired sound level and Left/Right (or Front/Rear) balance is achieved. If clipping distortion becomes audible, reduce the Input Trim level. If more signal reduction is needed, lower your line level from the source with the mixer’s master level controls.
Shielded drivers ensure the YSM2P-II’s can be located close to computer and video monitors or hard drive recording systems.
The YSM2P-II uses a bi-amplification system with separate power amps for the tweeter and the woofer The YSM2P-II utilizes an electronically active crossover network tuned specifically for each driver. This type of crossover network divides the signal much more precisely than traditional passive crossover networks.
Features:
- Bookmatched Left/Right pairs
- Bi-amplified operation features 32-watts of low frequency power and 14-watts for the high frequency
- Components include a 1-inch domed tweeter and a woven laminate cone 5 1/4-inch woofer
- Precisely tuned active crossover enables each driver to take advantage of the bi-amplification
- 1/4-inch TRS or XLR input jacks
- Input Trim control allows you to adjust the volume of each monitor
- Power switch is located at the rear of the enclosure
System Type: 2-Way
Active or Passive: Active
Program Power (Watts): 46
Biamp Operation Only: Yes
Max SPL (dB): 113
Frequency Response (Hz +/- 3db): 70 - 19,000
Crossover Frequency (Hz): 2,000
Driver Configuration: 5.25-inch / 1-inch
HF Driver(s): 1 inch Polyester Dome - Medium Viscosity Ferrofluid Cooled
HF Program Power (Watts): 14
LF Driver(s): 5.25-inch Woven Laminate cone - Ceramic magnet
LF Program Power(Watts): 32
Sheilding: Bucking Magnet
Total Power (Watts): 46
HF Power Amplifier (Watts): 14
HF Amplifier Type: AB
LF Power Amplifier (Watts): 32
LF Amplifier Type: AB
Cooling Scheme: Convection
Power Cable: Removeable IEC
Power Switch: Yes
Power Consumption (typ/max): 36VA / 72VA
Inputs: 1-XLR / 1-1/4-inch TRS
Inputs - 1/4" Jacks: 1 (TRS)
Inputs - XLR: 1
Input Sensitivity (Vrms Sine): 0.25
Level Controls: Input Sensitivity (off/-10dB)
Enclosure Materials: MDF Wood
Baffle Material: Gray PVC Clad MDF Wood
Port(s): 1-inch Vented
Covering / Finish: Charcoal Gray Laminate
Other Details: Shipped in Mirrored Pairs.
Dimensions (DWH xbackW, inches): 10.5 x 7.6 x 11.5
Dimensions (DWH xbackW, cm): 26.6 x 19.4 x 29.2
Weight (lbs/kg)System Type: 2-Way
Active or Passive: Active
Program Power (Watts): 46
Biamp Operation Only: Yes
Max SPL (dB): 113
Frequency Response (Hz +/- 3db): 70 - 19,000
Crossover Frequency (Hz): 2,000
Driver Configuration: 5.25-inch / 1-inch
HF Driver(s): 1 inch Polyester Dome - Medium Viscosity Ferrofluid Cooled
HF Program Power (Watts): 14
LF Driver(s): 5.25-inch Woven Laminate cone - Ceramic magnet
LF Program Power(Watts): 32
Sheilding: Bucking Magnet
Total Power (Watts): 46
HF Power Amplifier (Watts): 14
HF Amplifier Type: AB
LF Power Amplifier (Watts): 32
LF Amplifier Type: AB
Cooling Scheme: Convection
Power Cable: Removeable IEC
Power Switch: Yes
Power Consumption (typ/max): 36VA / 72VA
Inputs: 1-XLR / 1-1/4-inch TRS
Inputs - 1/4" Jacks: 1 (TRS)
Inputs - XLR: 1
Input Sensitivity (Vrms Sine): 0.25
Level Controls: Input Sensitivity (off/-10dB)
Enclosure Materials: MDF Wood
Baffle Material: Gray PVC Clad MDF Wood
Port(s): 1-inch Vented
Covering / Finish: Charcoal Gray Laminate
Other Details: Shipped in Mirrored Pairs.
Dimensions (DWH xbackW, inches): 10.5 x 7.6 x 11.5
Dimensions (DWH xbackW, cm): 26.6 x 19.4 x 29.2
Weight (lbs/kg): 12 / 5.412 / 5.4
|
|
|
|
|
|
|
|
|
|
0 Item
Download Product Features
